Motion & gravity

Vehicle Braking Dynamics Lab

Simulates a two-axle car braking in a straight line towards a hazard over up to four road zones (dry asphalt, wet asphalt, snow, ice), with the reaction and brake build-up time, load transfer to the front axle, an exponential slip-friction curve per surface, quasi-static wheels that roll, lock (ABS off) or are held at an ABS slip target (ABS on), and aerodynamic drag. Each road segment is an exact closed form, so the stopping distance and time, the speed at the hazard, the share of the stop with each axle at its limit, the ideal brake bias and a comparison car (ABS switched or the best possible braking) are exact; 161 animation frames, the braking segments and the friction curves follow. Refuses invalid inputs plainly, warns of a rear lock, and scores five challenges. For learning vehicle braking dynamics.

Last updated

Calculator overview

Inputs and outputs

This summary comes from the calculator's published input and output contract.

Inputs

Vehicle mass (required)
About this input

m, the vehicle mass in kg (it scales the axle loads and the drag deceleration).

Unit kg Default 1500 Range 800 to 3500
Wheelbase (required)
About this input

L, the distance between the axles, in m.

Unit m Default 2.7 Range 2.2 to 4
End of zone 1 (required)
About this input

b1, the end of zone 1 in m, measured from the front bumper when the hazard is seen.

Unit m Default 45 Range 0 to 2000
Reaction time (required)
About this input

tr, the driver's reaction time in s; the car runs on at full speed meanwhile.

Unit s Default 1 Range 0 to 3
ABS slip target (required)
About this input

The ABS slip target in %, used with Fixed slip target.

Unit % Default 15 Range 2 to 50
Your prediction (challenge 1) (required)
About this input

Your prediction for challenge 1: Not yet predicted, Stops before the hazard or Hits the hazard. Not used outside challenge 1.

Default Not yet predicted Allowed Not yet predicted, Stops before the hazard, Hits the hazard
Zone 2 surface (required)
About this input

The surface of zone 2 (from b1 to b2).

Default Wet asphalt Allowed Dry asphalt, Wet asphalt, Snow, Ice
Zone 3 surface (required)
About this input

The surface of zone 3 (from b2 to b3).

Default Dry asphalt Allowed Dry asphalt, Wet asphalt, Snow, Ice
Zone 4 surface (required)
About this input

The surface of zone 4 (from b3 on).

Default Wet asphalt Allowed Dry asphalt, Wet asphalt, Snow, Ice
End of zone 2 (required)
About this input

b2, the end of zone 2 in m, at or after b1 (equal boundaries make a zone of zero length).

Unit m Default 70 Range 0 to 2000
End of zone 3 (required)
About this input

b3, the end of zone 3 in m, at or after b2; zone 4 runs on without end.

Unit m Default 150 Range 0 to 2000
Zone 1 surface (required)
About this input

The surface of zone 1 (the road before b1, including the road under the car at the start): Dry asphalt, Wet asphalt, Snow or Ice.

Default Dry asphalt Allowed Dry asphalt, Wet asphalt, Snow, Ice
Centre of gravity height (required)
About this input

h, the height of the centre of gravity, in m; with the wheelbase it sets how much weight moves to the front under braking.

Unit m Default 0.55 Range 0.3 to 0.65
Challenge number (required)
About this input

Selects a challenge: 0 for none, 1 to 5 for a predefined challenge whose settings replace the inputs it fixes.

Default 0 Range 0 to 5
Comparison car (required)
About this input

The comparison car (a ghost): No comparison, ABS switched (the same stop with ABS the other way) or Best possible braking (both axles at their peak friction in every segment, whatever the pedal and bias).

Default ABS switched Allowed No comparison, ABS switched, Best possible braking
ABS (required)
About this input

ABS on: an axle at its friction limit is held at the ABS slip target. ABS off: it locks and slides at the locked friction.

Default ABS on Allowed ABS on, ABS off
ABS target (required)
About this input

Peak slip of each surface (ABS holds each wheel at its surface's friction peak) or Fixed slip target (at slipTarget, also past the peak).

Default Peak slip of each surface Allowed Peak slip of each surface, Fixed slip target
Brake build-up time (required)
About this input

tb, the time the brakes take to reach full force, in s; half of it is added to the reaction time (the standard half-time approximation).

Unit s Default 0.2 Range 0 to 1
Hazard position (required)
About this input

H, how far ahead the hazard is, in m.

Unit m Default 69 Range 5 to 2000
Initial speed (required)
About this input

v0, the speed in km/h when the driver sees the hazard.

Unit km/h Default 90 Range 10 to 150
Pedal demand (required)
About this input

The total deceleration the brake pedal asks for, in g (1 g = 9.80665 m/s2).

Unit g Default 0.8 Range 0.1 to 1
Drag area (required)
About this input

CdA, the drag coefficient times the frontal area, in m2 (0 means no drag); the drag deceleration is k v^2 with k = 1.225 CdA/(2 m).

Unit m2 Default 0.7 Range 0 to 1.5
Front brake bias (required)
About this input

The front brakes' share of the demanded brake force, in %.

Unit % Default 70 Range 30 to 90
Front weight share at rest (required)
About this input

The share of the weight on the front axle at rest, in %: it places the centre of gravity along the wheelbase.

Unit % Default 58 Range 40 to 65

Outputs

Reaction time used
About this output

The reaction time used, s (the challenge's when a challenge fixes it).

Unit s
Reaction distance
About this output

The distance covered during the reaction time, v0 tr, in m.

Unit m
Pedal demand used
About this output

The pedal demand used, g (the challenge's when a challenge fixes it).

Unit g
Friction against slip for each surface (41 points, dense near zero slip)
About this output

The friction-slip curve of each surface: 41 points at slip (j/40)^2 from 0 to 100%, dense near zero, with the friction of dry asphalt, wet asphalt, snow and ice.

No unit declared
Rear wheels lock first
About this output

Yes when, with ABS off, the rear wheels lock on some stretch while the front wheels still roll, else No. Blank while challenge 1 awaits a prediction.

No unit declared
Rear axle at its limit
About this output

The share of the braking distance with the rear axle at its friction limit, in %. Blank while challenge 1 awaits a prediction.

Unit %
Peak deceleration
About this output

The highest deceleration of the stop, tyres plus drag, in m/s2. Blank while challenge 1 awaits a prediction.

Unit m/s2
Initial speed used
About this output

The initial speed used, km/h (the challenge's when a challenge fixes it).

Unit km/h
Ideal front brake bias
About this output

The front brake bias at which both axles reach their peak friction at the same pedal, on the surface under the front axle when braking starts, in %.

Unit %
Hazard position used
About this output

The hazard position used, m (the challenge's when a challenge fixes it).

Unit m
Formula module versions
About this output

The formula modules the model is built from, with their versions.

No unit declared
Model version
About this output

The model version.

No unit declared
Model Status
About this output

NOT VALID with the reason when an input cannot be used; CHECK when the rear wheels lock while the front wheels still roll (ABS off), which a real car may not survive straight; otherwise OK. Not stopping before the hazard is a result, not a warning.

No unit declared
ABS slip target used
About this output

The ABS slip target used, % (the challenge's when a challenge fixes it).

Unit %
Zone 1 surface used
About this output

The zone 1 surface used (the challenge's when a challenge fixes it).

No unit declared
End of zone 3 used
About this output

The end of zone 3 used, m (the challenge's when a challenge fixes it).

Unit m
End of zone 2 used
About this output

The end of zone 2 used, m (the challenge's when a challenge fixes it).

Unit m
Zone 4 surface used
About this output

The zone 4 surface used (the challenge's when a challenge fixes it).

No unit declared
Zone 3 surface used
About this output

The zone 3 surface used (the challenge's when a challenge fixes it).

No unit declared
Zone 2 surface used
About this output

The zone 2 surface used (the challenge's when a challenge fixes it).

No unit declared
End of zone 1 used
About this output

The end of zone 1 used, m (the challenge's when a challenge fixes it).

Unit m
Stopping time
About this output

The time from seeing the hazard until the car stops, in s. Blank while challenge 1 awaits a prediction.

Unit s
Stopping distance
About this output

How far the front bumper travels from the moment the hazard is seen until the car stops, in m. Blank while challenge 1 awaits a prediction.

Unit m
Stops before the hazard
About this output

Yes when the car stops at or before the hazard (within 1E-9 relative), else No. Blank while challenge 1 awaits a prediction.

No unit declared
Wheelbase used
About this output

The wheelbase used, m (the challenge's when a challenge fixes it).

Unit m
Vehicle mass used
About this output

The vehicle mass used, kg (the challenge's when a challenge fixes it).

Unit kg
The four surfaces: the slip of peak friction, the peak and locked friction, and the friction the ABS holds
About this output

The four surfaces: the slip of peak friction in %, the peak and the locked friction, and the friction the ABS holds with the current target mode.

No unit declared
Challenge feedback
About this output

Feedback on the selected challenge: the prediction prompt, the met text or the not-met hint (blank with none).

No unit declared
Centre of gravity height used
About this output

The CG height used, m (the challenge's when a challenge fixes it).

Unit m
Car frames: 161 frames f = 0 to 160 at equal times to the end of the animation (your car's position, speed, deceleration, wheel angles and road segment, and the comparison car's position and speed)
About this output

The car frames: 161 rows, one per frame f = 0 to 160 at equal times to the end of the animation, each with the time in s, your car's position in m, speed in km/h and deceleration in m/s2, the front and rear wheel angles in degrees (a locked wheel stops turning), the road segment (0 before braking), and the comparison car's position in m and speed in km/h (blank with No comparison). While challenge 1 awaits a prediction only frame 0 is shown.

No unit declared
Challenge score
About this output

The challenge score: 100 when met, else 0.

No unit declared
Challenge: the value scored
About this output

The value the selected challenge scores: the room left before the hazard in m (challenges 1, 2 and 5), the larger of the two limit shares in % (3) or the slip target used in % (4); blank when not valid or withheld.

No unit declared
Challenge goal
About this output

The goal of the selected challenge (blank with none).

No unit declared
Build-up distance
About this output

The distance covered during half the brake build-up time, v0 tb/2, in m.

Unit m
Animation end time
About this output

The end time of the animation, in s: the later of the two cars' stopping times (yours alone with No comparison). Blank while challenge 1 awaits a prediction.

Unit s
ABS target used
About this output

The ABS target mode used (the challenge's when a challenge fixes it).

No unit declared
ABS used
About this output

The ABS setting used (the challenge's when a challenge fixes it).

No unit declared
Braking segments of your car: a new segment starts wherever either axle crosses onto another surface (each axle's state, load, friction used and slip, and the tyre deceleration)
About this output

The braking segments of your car: 7 rows, one per segment (a new one starts wherever either axle crosses a zone boundary); each travelled segment shows where it starts and ends in m, the surface under each axle, each axle's state (Rolling, ABS or Locked), its load in kN, the friction it uses, its slip in % and the tyre deceleration in m/s2; a segment not travelled shows only its number.

No unit declared
Braking distance
About this output

The distance covered with the brakes fully applied, in m (the stopping distance less the reaction and build-up distances). Blank while challenge 1 awaits a prediction.

Unit m
Brake build-up time used
About this output

The brake build-up time used, s (the challenge's when a challenge fixes it).

Unit s
Challenge result
About this output

No challenge selected, MET or NOT MET.

No unit declared
Front axle at its limit
About this output

The share of the braking distance with the front axle at its friction limit (locked with ABS off, held with ABS on), in %. Blank while challenge 1 awaits a prediction.

Unit %
Front brake bias used
About this output

The front brake bias used, % (the challenge's when a challenge fixes it).

Unit %
Equivalent constant deceleration
About this output

The constant deceleration that would give the same braking distance, v0^2/(2 times the braking distance), in g. Blank while challenge 1 awaits a prediction.

Unit g
Room left before the hazard
About this output

The room left before the hazard, H less the stopping distance, in m; negative when the car reaches the hazard. Blank while challenge 1 awaits a prediction.

Unit m
Speed at the hazard
About this output

The speed at which the car reaches the hazard, in km/h; blank when it stops before it. Blank while challenge 1 awaits a prediction.

Unit km/h
Front weight share at rest used
About this output

The front weight share used, % (the challenge's when a challenge fixes it).

Unit %
Drag area used
About this output

The drag area used, m2 (the challenge's when a challenge fixes it).

Unit m2
Comparison stopping distance
About this output

The comparison car's stopping distance, in m. Blank with No comparison. Blank while challenge 1 awaits a prediction.

Unit m
Comparison stops before the hazard
About this output

Yes when the comparison car stops before the hazard, else No. Blank with No comparison. Blank while challenge 1 awaits a prediction.

No unit declared
Comparison minus your car
About this output

The comparison car's stopping distance less yours, in m. Blank with No comparison. Blank while challenge 1 awaits a prediction.

Unit m
Time before full braking
About this output

The time before full braking, tr + tb/2, in s.

Unit s
Comparison car used
About this output

The comparison used (the challenge's when a challenge fixes it).

No unit declared
Comparison stopping time
About this output

The comparison car's stopping time, in s. Blank with No comparison. Blank while challenge 1 awaits a prediction.

Unit s
This page is provided by LogicCommons for informational purposes only. Results are analysis outputs computed from the inputs you supply and are not professional advice. Verify all inputs and results independently.

LogicCommons is in beta. If a result, label, or reference looks wrong, tell us here; we read every message.

Methodology

Purpose and model boundary

This lab simulates a two-axle car braking in a straight line towards a hazard. The road ahead is split into up to four zones of dry asphalt, wet asphalt, snow or ice, and each axle runs on the zone under it, so the front and rear axles can be on different surfaces. After the driver's reaction time and half the brake build-up time, the brakes act: weight moves to the front axle, the pedal's demand is shared between the axles by the brake bias, each tyre follows an exponential slip-friction curve with a peak, an axle that asks for more than its tyres can give locks (ABS off) or is held at an ABS slip target (ABS on), and aerodynamic drag acts on the body. Each stretch of road between surface changes is solved exactly in closed form. The lab returns the stopping distance and time, whether the car stops before the hazard or the speed at which it reaches it, the share of the stop with each axle at its limit, the ideal brake bias, a comparison car, the braking segments, 161 animation frames and the friction curves. Five scored challenges use the same model.

It is a lab for learning braking dynamics: why the stopping distance grows with the square of the speed, why a locked wheel stops a car later than a rolling one, why the front brakes do most of the work, what ABS does and why its best slip target sits at the peak of the friction curve. It is not an accident reconstruction or a vehicle design tool. The wheels are quasi-static, friction depends only on slip and surface, and yaw, steering and the ABS pressure cycle are not modelled: a rear lock is warned about, not simulated.

The model is the calculation authority. The page sends the values you set to the model and draws only what it returns: the road zones and the hazard, your car and the comparison car frame by frame with their wheels turning or locked, the speed and deceleration charts, and the friction curves with each axle's operating point. The page computes no distance, speed, friction or lock itself.

Inputs and units

Positions are measured from the car's front bumper at the moment the driver sees the hazard.

Input Meaning and unit
Initial speed v₀, from 10 to 150 km/h (default 90 km/h).
Reaction time tr, from 0 to 3 s (default 1 s); the car runs on at full speed meanwhile.
ABS ABS on or ABS off (default ABS on).
End of zone 1, 2, 3 b₁ ≤ b₂ ≤ b₃, each from 0 to 2,000 m (defaults 45, 70 and 150 m). Equal boundaries make a zone of zero length; zone 4 runs on without end.
Zone 1 to 4 surface Dry asphalt, Wet asphalt, Snow or Ice (defaults Dry, Wet, Dry, Wet). Zone 1 includes the road under the car at the start.
Hazard position H, from 5 to 2,000 m ahead (default 69 m).
Pedal demand The total deceleration the pedal asks for, from 0.1 to 1.0 g (default 0.8 g; 1 g = 9.80665 m/s²).
Front brake bias The front brakes' share of the demanded brake force, from 30% to 90% (default 70%).
Centre of gravity height h, from 0.30 to 0.65 m (default 0.55 m).
Wheelbase L, from 2.2 to 4.0 m (default 2.7 m).
Front weight share at rest From 40% to 65% (default 58%); it places the centre of gravity along the wheelbase.
Vehicle mass m, from 800 to 3,500 kg (default 1,500 kg).
Drag area CdA, from 0 to 1.5 m² (default 0.7 m²); 0 means no drag.
Brake build-up time tb, from 0 to 1 s (default 0.2 s).
ABS target Peak slip of each surface (default) or Fixed slip target.
ABS slip target From 2% to 50% (default 15%), used with Fixed slip target.
Comparison car No comparison, ABS switched (default) or Best possible braking.
Challenge number 0 for free exploration, or 1 to 5 to load a challenge.
Your prediction (challenge 1) Not yet predicted, Stops before the hazard or Hits the hazard. Used only in challenge 1.

Where each input is set:

  • On the canvas only: the three zone ends and the hazard (drag them along the road, or use the arrow keys; Enter gives an exact position), the four zone surfaces (tap a zone to choose its surface) and your prediction for challenge 1.
  • In the input panel: every other input.

Governing relationships

Before braking. Full braking starts after the dead time tr + tb/2, the reaction time plus half the build-up time (the standard half-time approximation). Meanwhile the car covers the reaction distance v₀·tr and the build-up distance v₀·tb/2 at full speed, without drag.

The friction curve. With the slip λ from 0 (free rolling) to 1 (locked), each surface follows the exponential (Burckhardt) curve μ(λ) = c₁·(1 - e^(-c₂·λ)) - c₃·λ, with published coefficients for typical tyres. It peaks at the slip λ* = ln(c₁·c₂/c₃)/c₂; a locked wheel slides at μ(1). On these coefficients the peak slip, peak friction and locked friction are about 17.0%, 1.170 and 0.760 on dry asphalt, 13.1%, 0.801 and 0.510 on wet asphalt, and 6.0%, 0.190 and 0.130 on snow. Ice has no interior peak (c₃ = 0): its curve rises all the way to full slip, so its peak and locked friction are equal at 0.050 and ABS cannot beat a locked wheel there. With ABS the limiting friction is the peak, or the friction at the fixed slip target, also when that target lies past the peak.

Load transfer. With l_r = (front weight share)·L the distance from the centre of gravity to the rear axle and l_f = L - l_r to the front, the axle loads per unit mass at a tyre deceleration a are

n_f = (g·l_r + a·h) / L, n_r = (g·l_f - a·h) / L.

Braking moves weight to the front. The CG height stops at 0.65 m so the rear wheels can never lift.

The axles in one stretch of road. The pedal demands a deceleration a_D = (pedal)·g, split into D_f = β·a_D at the front and D_r = a_D - D_f at the rear, with β the front bias. An axle is limited when its demand exceeds its friction times its load. The tyre deceleration has a closed form for each case: nothing limited a = a_D; front limited a = (μ_f·g·l_r/L + D_r) / (1 - μ_f·h/L); rear limited a = (μ_r·g·l_f/L + D_f) / (1 + μ_r·h/L); both limited a = g·(μ_f·l_r + μ_r·l_f) / (L - μ_f·h + μ_r·h), where μ is the locked friction (ABS off) or the ABS friction (ABS on). Which axle reaches its limit first is found by imagining the pedal pressed from 0 to the demand: the axle that reaches its limit at the lower pedal goes first, and the other is then tested with the first one limited. With ABS off a locked wheel stays locked within the stretch.

Ideal brake bias. On the surface under the front axle when braking starts, with peak friction μ*, the bias 100·(l_r + μ*·h)/L % lets both axles reach their peak at the same pedal.

Motion in one stretch (exact). With a constant tyre deceleration a and drag deceleration k·v², where k = 1.225·CdA / (2m) (air density 1.225 kg/m³), the speed after a distance x from a start speed v_s is

v²(x) = (v_s² + a/k)·e^(-2kx) - a/k,

the distance to stop is ln(1 + k·v_s²/a) / (2k), and the time follows from the arctangent form of the same equation. With no drag these reduce to v² = v_s² - 2ax and a stopping distance of v_s²/(2a). A new stretch starts wherever either axle crosses a zone boundary (the front axle sits 0.9 m behind the bumper), so a stop has up to seven stretches.

Results. The stopping distance is the reaction and build-up distances plus the braking distance. The equivalent constant deceleration is v₀² / (2·braking distance), in g. The car stops before the hazard when its stopping distance is at most H (within 1×10⁻⁹ relative); otherwise the speed at the hazard is read from the stretch in which it lies.

The comparison car shares the road, the speed and the dead time, with ABS switched the other way, or with Best possible braking: both axles at their peak friction in every stretch, whatever the pedal and bias.

Calculation sequence

  1. Check the inputs in the order of the list under Errors and warnings.
  2. Take the values used: in a challenge, its own settings, except the inputs it leaves to you. The prediction is never replaced.
  3. Compute the friction curve of each surface and its peak, locked and ABS friction.
  4. Compute the dead time and the reaction and build-up distances, then the positions where each axle crosses each zone boundary, and the stretches between them.
  5. In each stretch, for your car and the comparison car, find which axles are limited and the tyre deceleration.
  6. Solve each stretch exactly in order until the car stops.
  7. Compute the shares at the limit, the rear-lock warning, the peak and equivalent deceleration, the ideal bias, each rolling axle's operating slip (for display), and the 161 frames.
  8. Set the status and, in a challenge, score it.

Outputs and interpretation

  • Stopping distance (m) and stopping time (s), split into the reaction distance, build-up distance and braking distance, with the time before full braking.
  • Room left before the hazard (m, negative when the car reaches it), stops before the hazard (Yes or No) and the speed at the hazard (km/h, blank when it stops before).
  • Front axle at its limit and rear axle at its limit: the share of the braking distance with that axle locked (ABS off) or held (ABS on), in %.
  • Rear wheels lock first: Yes when, with ABS off, the rear locks on some stretch while the front still rolls.
  • Peak deceleration (m/s², tyres plus drag) and equivalent constant deceleration (g).
  • Ideal front brake bias (%).
  • The comparison car: its stopping distance and time, the difference from yours, and whether it stops before the hazard.
  • Tables: the braking segments (where each starts and ends, the surface under each axle, each axle's state Rolling, ABS or Locked, its load in kN, the friction it uses, its slip, and the tyre deceleration), the four surfaces (peak slip, peak, locked and ABS friction), the friction curves of all four surfaces, and the car frames (time, position, speed, deceleration, wheel angles, segment, and the comparison car's position and speed).

Reading the canvas: the two cars move along the road at equal time steps; a locked wheel stops turning. The friction curves mark where each axle operates: on the rising side of the curve while it rolls, at the target while ABS holds it, at full slip when it is locked. The speed chart shows the stretch where the car reaches a slippery zone and its deceleration drops.

Challenges

Every challenge fixes its own road and car and leaves the named inputs to you. The model scores each challenge MET (100 points) or NOT MET (0), shows the value it scored, and gives a one-line hint while it is not met.

  1. Predict the stop. Predict whether the car stops before the hazard on a wet road with ABS off and the pedal pressed hard. It is met when your prediction matches the outcome; the value scored is the room left before the hazard.
  2. Stop on a wet road. Stop before the hazard 60 m ahead on a wet road from 80 km/h. Choose ABS, the pedal and the brake bias. The value scored is the room left before the hazard.
  3. Balance the brakes. With ABS off and the pedal at 0.75 g on a wet road, set the front brake bias so neither axle locks. The value scored is the larger of the two shares at the limit; it is met at exactly 0.
  4. Tune the ABS on snow. On snow, set the ABS slip target within 1 percentage point of the slip where snow grips best. The value scored is the slip target used.
  5. Ice patch ahead. Find the highest speed from which the car still stops before the hazard, with no more than 3 m to spare. The value scored is the room left before the hazard; it is met when the car stops before the hazard with at most 3 m to spare.

Challenge 1 holds back the answer until you predict. While your prediction reads Not yet predicted, the stopping distance and time, the braking distance, the hazard results, the limit shares and rear-lock warning, the decelerations, the comparison car's results and the animation end time are blank, the braking segments show only their numbers, and only frame 0 is shown; the challenge reads NOT MET with a prompt to predict first. The reaction and build-up distances, the ideal bias, the surfaces and the friction curves stay shown. Your prediction changes nothing outside challenge 1.

What to take from the lab: most of a stop at speed is spent before the brakes bite and in the square of the speed; a sliding tyre grips less than one held near its peak; and the brake bias must follow the weight that moves forward.

Validation and status logic

The status reads the first match in the list under Errors and warnings. The NOT VALID checks run on the values you entered, also while a challenge is selected; the rear-lock CHECK runs on the values used, also inside challenges. Not stopping before the hazard is a result, never a warning. A challenge number that is not a whole number from 0 to 5 counts as no challenge selected.

Assumptions and limitations

  • Straight-line braking of a two-axle car with static load transfer (no pitch dynamics); drag acts on the body but is left out of the load transfer and does not act before the brakes do.
  • One friction curve per surface, with no dependence on speed, load or temperature; published, rounded coefficients for typical tyres. Ice has no friction peak in this table, so ABS cannot beat a locked wheel on ice here.
  • Quasi-static wheels: no wheel-spin dynamics, no ABS pressure cycling; with a fixed target past the peak, ABS is held at the target friction. Within a stretch a locked wheel stays locked; at a surface change each axle is decided afresh.
  • A constant pedal through the stop and the half-time build-up approximation.
  • No yaw, steering or lateral forces: a rear lock is flagged, not simulated.
  • Speeds 10 to 150 km/h, positions to 2,000 m; the CG height stops at 0.65 m so the rear wheels never lift.
  • A value within 1×10⁻⁹ (relative) of a threshold may flip a lock decision, the hazard result or a challenge.

Restrictions and non-computing states

Under NOT VALID every result, segment, frame and curve is blank; a selected challenge reads NOT MET with a score of 0, and its goal and hint stay shown. With No comparison, the comparison car's results and frames are blank. In challenge 1, until you predict, the results are held back as described under Challenges.

Errors and warnings

The status messages, first match wins:

  • NOT VALID: the initial speed must be from 10 to 150 km/h and the reaction time from 0 to 3 s
  • NOT VALID: choose ABS on or ABS off
  • NOT VALID: the three zone boundaries must be from 0 to 2000 m, each at or after the one before
  • NOT VALID: choose a surface from the list for each of the four zones
  • NOT VALID: the hazard must be from 5 to 2000 m ahead
  • NOT VALID: the pedal demand must be from 0.1 to 1.0 g and the front brake bias from 30 to 90%
  • NOT VALID: the CG height must be from 0.30 to 0.65 m, the wheelbase from 2.2 to 4.0 m and the front weight share from 40 to 65%
  • NOT VALID: the mass must be from 800 to 3500 kg, the drag area from 0 to 1.5 m2 and the brake build-up time from 0 to 1 s
  • NOT VALID: choose an ABS target mode from the list, with a slip target from 2 to 50%
  • NOT VALID: choose a comparison from the list
  • NOT VALID: the challenge number must be a whole number from 0 to 5, and the stop prediction one of the listed choices
  • CHECK: the rear wheels lock while the front wheels still roll. A real car can slide sideways or spin here, which this straight-line model does not show. Move the brake bias forward or switch ABS on: ABS off only.
  • OK: the inputs are valid and the rear wheels do not lock first.

References

This laboratory is an educational model of straight-line braking. The stopping distance is the distance covered during the driver's reaction and the brake build-up plus the braking distance. While braking, weight moves to the front axle in proportion to the deceleration, each tyre's grip follows the exponential (Burckhardt) slip-friction curve of its surface, an axle past its limit locks or is held by ABS at a slip target, and aerodynamic drag adds a deceleration proportional to the square of the speed. Each stretch of road is solved exactly for a constant tyre deceleration plus quadratic drag.

Sources and further reading

  • The exponential (Burckhardt) slip-friction model, its coefficients for dry asphalt, wet asphalt and snow, the braking slip and the optimal slip at the peak of the curve: F. Crocetti, G. Costante, M. L. Fravolini and P. Valigi, "A data-driven slip estimation approach for effective braking control under varying road conditions", 2020 28th Mediterranean Conference on Control and Automation (MED), IEEE, 2020, pages 496-501. arXiv:2211.02558
  • Tyre-road friction models and anti-lock braking control: U. Kiencke and L. Nielsen, Automotive Control Systems: For Engine, Driveline, and Vehicle, 2nd edition, Springer, 2005.
  • Load transfer under braking, the brake force distribution and which axle locks first: T. D. Gillespie, Fundamentals of Vehicle Dynamics, SAE International, 1992, chapter 3, Braking Performance.
  • Stopping sight distance as the distance travelled during the perception-reaction time plus the distance travelled while braking: Federal Highway Administration, Self-Enforcing Roadways: A Guidance Report, FHWA-HRT-17-098, chapter 3, Relationship Between Speed and Geometric Design. Federal Highway Administration
  • The drag equation, drag = drag coefficient times air density times speed squared times reference area over 2: NASA Glenn Research Center, Drag Equation, Beginner's Guide to Aeronautics. NASA Glenn Research Center

No table or text from any of these publications is reproduced, and none of their authors or publishers has reviewed or endorses this laboratory.

This laboratory is for learning. Its results hold only within its stated ranges; the car brakes in a straight line on idealised surfaces with no yaw, so its distances are not those of any real car or road.

Links were current at build time. If one moves, search the document's title rather than reporting a broken link as a defect.

Results are informational and not professional advice. See our Terms of Use. Powered by SpreadsheetWeb · About · Privacy · Terms